Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles
Filter by: Popular Clear All
  • 3f05q's Avatar
    Today, 12:13 PM
    3f05q replied to a thread 2.3-16 Project in Member's Rides
    ...and nearly a month later the decision has been made to have JE make spacers.
    34 replies | 3862 view(s)
  • Stevester 500e's Avatar
    Yesterday, 08:01 PM
    I was inter-web day dreaming and ran across this web page https://www.engineswapdepot.com/?p=7844https://www.engineswapdepot.com/?p=7844
    4094 replies | 655099 view(s)
  • secretmachine's Avatar
    07-08-2018, 01:23 PM
    secretmachine replied to a thread the swifteenV in Member's Rides
    I'll be switching from delrin to poly on this car. the delrin will go into darkwing since they are still ok shape.
    142 replies | 28817 view(s)
  • chrisfball12's Avatar
    07-08-2018, 01:06 AM
    chrisfball12 replied to a thread the swifteenV in Member's Rides
    What subframe bushings will you be using?
    142 replies | 28817 view(s)
  • secretmachine's Avatar
    07-07-2018, 11:32 PM
    secretmachine replied to a thread the swifteenV in Member's Rides
    Yes they are. I'll be making a thread for it, there will be a full service option and weld your own. The toe mods will need to be a serviced option...
    142 replies | 28817 view(s)
  • secretmachine's Avatar
    07-07-2018, 11:27 PM
    secretmachine replied to a thread the swifteenV in Member's Rides
    Thanks Alain!
    142 replies | 28817 view(s)
  • Maximb's Avatar
    07-07-2018, 11:55 AM
    Maximb replied to a thread the swifteenV in Member's Rides
    Are these going to be for sale?
    142 replies | 28817 view(s)
  • Alain V.'s Avatar
    07-06-2018, 01:17 PM
    Alain V. replied to a thread the swifteenV in Member's Rides
    Wow, lots of time and work- you put into that rear subframe. very nice:cool2:
    142 replies | 28817 view(s)
  • secretmachine's Avatar
    07-05-2018, 07:38 PM
    secretmachine replied to a thread the swifteenV in Member's Rides
    here it is guys, the broken subframe. nose area split right down the middle, lot's of upward forces here. cracks on the edge of the front...
    142 replies | 28817 view(s)
  • secretmachine's Avatar
    07-05-2018, 07:34 PM
    secretmachine replied to a thread the swifteenV in Member's Rides
    so what can we do here? cool little fold here to make the box super strong and tied in even more to the rear diff plane.
    142 replies | 28817 view(s)
  • secretmachine's Avatar
    07-05-2018, 07:30 PM
    secretmachine replied to a thread the swifteenV in Member's Rides
    "Upcycling" some of the oem 5-link bushings into spacers. Creating the uprights.
    142 replies | 28817 view(s)
  • secretmachine's Avatar
    06-26-2018, 01:09 PM
    I was taught that the oiling hole is called edm, if that's not the terminology these days, you still understand what I mean. That is how the pin gets...
    34 replies | 3862 view(s)
  • Hexadeca's Avatar
    06-25-2018, 06:32 PM
    Hexadeca replied to a thread 2.3-16 Project in Member's Rides
    Your rods are rifle drilled, and its not relevant, and it may not have been accomplished by drilling. "edm" is a term used for push rods if its used...
    34 replies | 3862 view(s)
  • 3f05q's Avatar
    06-25-2018, 01:07 PM
    3f05q replied to a thread 2.3-16 Project in Member's Rides
    Good to know. how much total clearance should there be? I don't know. Do all factory rods have them? Would that affect decisions as far as how...
    34 replies | 3862 view(s)
  • secretmachine's Avatar
    06-25-2018, 12:47 PM
    using spacers should be ok, common practice there. do your rods have edm oiling hole through them?
    34 replies | 3862 view(s)
  • 3f05q's Avatar
    06-25-2018, 10:49 AM
    3f05q replied to a thread 2.3-16 Project in Member's Rides
    I doubt I can take that kind of action at this point, and I'm trying to involve myself now as much as possible. This. Everything I see...
    34 replies | 3862 view(s)
  • Hexadeca's Avatar
    06-22-2018, 08:30 PM
    Hexadeca replied to a thread 2.3-16 Project in Member's Rides
    This is why manufacturers should not be so stingy with part numbers. If the crank, rods and pistons are different, you got a different engine that...
    34 replies | 3862 view(s)
  • 3f05q's Avatar
    06-22-2018, 07:03 PM
    3f05q replied to a thread 2.3-16 Project in Member's Rides
    F This motor has been at the machine shop for a full year now. Thanks for the information. The story I'm told I'd they sent off a piston to...
    34 replies | 3862 view(s)
  • secretmachine's Avatar
    06-22-2018, 05:39 PM
    crank guided rods are 102 030 01 20 piston guided are 102 030 05 20 to 102 030 26 20 your 014121 build number is past 003000
    34 replies | 3862 view(s)
  • 3f05q's Avatar
    06-22-2018, 02:19 PM
    3f05q replied to a thread 2.3-16 Project in Member's Rides
    Do you know the engine number cutoff for the change? My Engine: 10298310014121
    34 replies | 3862 view(s)
  • secretmachine's Avatar
    06-22-2018, 02:11 PM
    early engines are crank guided, later engines are piston guided.
    34 replies | 3862 view(s)
  • 3f05q's Avatar
    06-22-2018, 12:50 PM
    3f05q replied to a thread 2.3-16 Project in Member's Rides
    Just went to pick up the assembled bottom end from the machine shop. I checked it out and the pistons they ordered up from Wiseco do NOT guide the...
    34 replies | 3862 view(s)
More Activity